1-877-443-6276

GeoMD - GeoAlarm Wireless GeoSeries® Encrypted Pet-Immune Motion Detector

Item# GEOMD

Average Customer Rating:
Read Review(s) | Write a Review

List Price: ~~$43.47~~

Our Price: $28.98

Availability: In Stock

QTY:

Shipping3-5 Business Days

Returns30-Day Return Window

PaymentSecure Transaction

Description
Specifications
Installation
Battery
Pin Function
Pet Immunity
Sensitivity
DIY Videos
Compatible

GeoSeries GeoMD Motion Sensor Description:

The GeoMD is a wireless GeoSeries® encrypted PIR motion detector with adjustable 33 to 55 lbs. pet immunity, that is designed to fit seamlessly in the corner of any room. When the passive-infrared sensor detects movement, the GeoMD then transmits an alarm notification signal to the GeoAlarm control panel (GeoCP-AT/GeoCP-VZ), end-user, and/or GeoArm central monitoring station informing everyone selected of an alarm initiating event.

We recommend using the provided screws for the GeoMD installation. This method is more secure than using the adhesive alone. Select the desired position for the sensor. Keep in mind, that the sensor detects motion within 3.28 ft (1m) in front of it installed at 6.88 ft (2.1m) having a range of 32.80 ft (10m). We recommend mounting the detector between 7.5 to 9.5 feet above the ground, and aiming it at a highly trafficked area. The GeoMD detects motion from 19.68 (6m) to 32.80 (10m) feet using an 90 degree detection angle.

The GeoMD requires a CR123A battery, that provides approximately 6 years of life (with average use x100 per day). Once the battery is low, the GeoAlarm GeoCP panel displays a low battery icon next to the sensor in the devices list. The battery must be replaced within 7 days of the first low battery notification. If the battery is not replaced within 7 days, the sensor may not function properly.

Product Features:

433 MHz Window/Door Transmitter
Detection Range up to 32.8 ft. (10m)
Low & High Sensitivity Modes
Adjustable Pet Immunity (from 33 to 55 lbs.)
Long Range up to 820' Open Air
1-Way Encryption
Tamper Supervised
Long Battery Life (Up to 5 years)
Includes CR123A Lithium Battery 3V
Self-Stick Tape and/or optional screws for mounting
Complies UL 639,ULC S306

GeoSeries GeoMD Motion Sensor Specifications:

Sensor Dimensions (W x H x D): 2.16 x 2.99 x 1.65 in. (55 x 76 x 42 mm)
Wireless Signal Range: 820.21 ft. (250 m)
Transmitter Frequency: 433 MHz
Encryption: Yes (1-way)
Pet Immunity: 33 to 55 lbs. dog
Detection Length (Default): 32.80 ft. (10 m)
Detection Length (Optional): 19.68 ft. (6 m)
Detection Angle: 90 degree
Mounting Height: 7.5 to 9.5 ft. (2.28 to 2.89 m)
Mounting Options: Adhesive, Screw
Pairing Method: Button Trigger
Transmitted Indications: Tamper (Cover), Low Battery
Battery Type: CR123A (1300mAh)
Battery Life: 6 years (x100 per day)
Power: 4mA
Supervision: Yes (60 minutes heartbeat)
Operating Temperature: 32 to 122°F (0 to 50°C)
Certifications: FCC, UL639, ULC S306-03

GeoSeries GeoMD Motion Sensor Installation:

The GeoMD motion sensor can be installed using the provided adhesive and/or screws. We recommend using the provided screws for installation. This method is more secure than using adhseive alone.

Please Note - Add the motion detector to the GeoAlarm control panel before installation.

Important Safety Instructions:

Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
When there is a low battery, replace with a compatible lithium ion battery.

To install the motion detector:

1. Select the desired position for the sensor. The sensor detects motion within 3.28 ft (1m) in front of it installed at 6.88 ft (2.1m) having a range of 32.80 ft (10m).
2. Remove the sensor's battery pull tab.
3. Adhere the sensor to the wall using the provided screws and/or adhesive. We recommend using the provided screws for installation. This method is more secure than using adhesive.

Using Screws
a. Locate the bottom of the sensor (the slotted short end), and then use a screwdriver to remove the casing's screw.
b. Gently slide a fingernail/fingertip into the slot and push the top casing of the sensor upward. (You can see the FCC label on the inside of sensor casing.)
c. Remove the adhesive film cover and then place the back plate against the wall, making sure that the orientation is correct for the desired position. Note, once placed the sensor cannot be moved without damaging the adhesive. (Optional)
d. Insert the included mounting screw into the screw breakaway screw hole, using a screwdriver to fully secure the backplate to the wall.
e. Before finishing installation, set the PINs and jumpers to the desired position.
f. Once the sensor is configured as desired, press the sensor cover against the base, until there is an audible snap.
g. Use the sensor's casing screw to secure the cover.

Using Adhesive
a. Locate the bottom of the sensor (the slotted flat end), and then use a screwdriver to remove the casing's screw.
b. Gently slide a fingernail/fingertip into the slot and push the top casing of the sensor upward.
c. Set the PINs and jumpers to the desired position.
d. Once the sensor is configured as desired, press the sensor cover against the base, until there is an audible snap.
e. Use the sensor's casing screw to secure the cover.
f. Peel the film cover off the adhesive, and then firmly press the sensor back plate against the wall. Once placed the sensor cannot be moved without damaging the adhesive.
h. Remove the adhesive film cover, and then place the back plate against the wall, making sure that the orientation is correct for the desired position. Note, once placed the sensor cannot be moved without damaging the adhesive.
i. Insert the included mounting screw into the screw breakaway screw hole, using a screwdriver to fully secure the backplate to the wall.
j. Before finishing installation, set the PINs and jumpers to the desired position.
k. Once the sensor is configured as desired, press the sensor cover against the base, until there is an audible snap.
l. Use the sensor's casing screw to secure the cover.
4. Add the sensor to the GeoAlarm control panel, by putting the panel in learn mode. Then press the button on the side of the sensor to pair the sensor to the panel. 5. Once added, test the sensor. Look at the GeoAlarm panel, and then open the door/window. Notice that the added sensor displays faulted.

Note: Testing all sensors to the GeoArm alarm monitoring station is strongly advised.

GeoSeries GeoMD Motion Sensor Battery Replacement:

The GeoMD motion detector requires a CR123A battery. Once the battery is low, the GeoAlarm panel displays a low battery icon next to the sensor in the devices list. The battery must be replaced within 7 days of the first low battery notification. If the battery is not replaced within 7 days, the sensor may not function property.

To Replace the Battery:

1. Locate the bottom of the sensor (the slotted flat end), and then use a screwdriver to remove the casing's screw.
2. Gently slide a fingernail/fingertip into the slot and push the top casing of the sensor outward, away from the wall.
3. Use a fingernail/fingertip to push the battery out of the casing, noting the polarity of the battery.
4. Insert a new CR123A battery into the battery casing, making sure that the polarity is correct.
5. Press the sensor cover back onto its back plate. There will be an audible snap.
6. Use the sensor's casing screw to secure the cover.
7. Test the sensor.

Warning: If an incompatible replacement battery is used, or the battery is installed incorrectly explosion or damages may occur.

GeoSeries GeoMD Motion Sensor Pin Function:

The PIR Motion Sensor has 2 sets of adjustable pins. The pins adjust the Pet Immunity setting and the Sensivity level. Each set of pins has 2 settings that can be selected.

Pin Configuration:

Top and middle pin - Pet Immunity (up to 33lb dog), Sensitivity Low - max of 19ft (6m) distance range
Middle and bottom pin - Pet Immunity (up to 55lb dog), Sensitivity Low - max of 32ft (10m) distance range

GeoSeries GeoMD Motion Sensor Pet Immunity:

The PIR Motion Sensor has pet immunity pins that allow the user to select the desired immunity level. Place the selector over the desired pin configuration.

To change the pet immunity level:

1. Remove the back plate from the motion sensor.
2. Turn the sensor over so the battery faces up.
3. Locate the pet immunity pins on the left side.
4. Gently pinch the jumper and pull upward and away from the sensor. All 3 pins are then visible.
5. Gently press the jumper on the desired pin set.
6. Replace the sensor plate, and then continue to installation.

or

Adjust the sensitivity level, and then continue to installation.

GeoSeries GeoMD Motion Sensor Sensitivity Level:

The PIR Motion Sensor has sensitivity pins that allow the user to select the desired sensitivity level. Place the selector over the desired pin configuration.

To change the sensitivity level:

1. Remove the back plate from the motion sensor.
2. Turn the sensor over so the battery faces up.
3. Locate the sensitivity pins on the right side.
4. Gently pinch the jumper and pull upward and away from the sensor. All 3 pins are then visible.
5. Gently press the jumper on the desired pin set.
6. Replace the sensor plate, and then continue to installation.

or

Adjust the pet immunity level, and then continue to installation.

GeoSeries GeoMD Motion Sensor Video Playlist:

GeoSeries GeoMD Motion Sensor Compatibility:

GeoCP-AT Control Panel
GeoCP-VZ Control Panel

▼ GeoSeries® Encrypted Security Sensors ▼

GeoCT - GeoAlarm Wireless GeoSeries® Encrypted Door/Window Contact

List Price: ~~$23.97~~

Our Price: $15.98