PROSiXHEATV - Resideo Honeywell Home Wireless Heat Detector (for ProSeries Control Panels)
ProSeries PROSiXHEATV Product Description:
The Resideo Honeywell Home PROSiXHEATV is a wireless heat detector that is intended for use with control panels that support PROSiX-Series devices. The PROSiXHEATV heat detector is compatible with the ProSeries PROA7, ProSeries PROA7C, ProSeries PROA7PLUS or ProSeries PROA7PLUSC all-in-one wireless touchscreen control panels. The PROSiXHEATV multi-criteria heat detector employs advanced levels of detection and discrimination. It reduces common cooking nusiance alarms and allows faster detection to different types of high temperature conditions.
To enroll and setup the device, you must enroll it in the control panel. When prompted, activate the PROSiXHEATV by pulling the battery tab or, if already powered, press the Test button to enroll. If the detector is not successfully enrolled during the enrollment period, the LED turns off and the device powers down. Activate the tamper or press the Test Button to restart the enrollment. The enrollment time varies depending on the signal strength between the device and the control panel. Once enrolled in a system, the detector cannot be used with another system until it is removed from the current one.
The PROSiXHEATV detects for two specific heat conditions; fixed heat above 135° F and rate-of-rise detection for greater than 104° and 15°F temperature rise per minute. The detector alarms when 135° F; is exceeded and restores when it falls below 135° F. However, the thermistor is damaged at 195° F and the integrity of the detector itself is compromised and needs to be replaced if that occurs. It also sends maintenance signals when the chamber is contaminated and requires cleaning. An end-of-life signal will be sent when the device is no longer functional and needs to be replaced entirely. A base tamper signal will be sent to to the control panel when the heat head is removed from the base. A supervision signal is sent to the panel every 200 seconds to check-in for system compatibility. And last but not least a signal and battery strength signal is sent so you know when the sensor is out of range or the batteries are low and need replacement. If programmed into the control panel to operate in One-Go-All-Go mode, all smoke detectors programmed as One-Go-All-Go in the system will sound on alarm.
The PROSiXHEATV tamper will alert if the detector is removed from the base. It will send a tamper signal to the control panel. The tamper can be made tamper-proof to prevent unauthorized removal from the base. To do so, simply break off the small pillar on the base. This causes the detector to latch to the base. Form this point on, to remove the detector from its base, you must use a small screwdriver to release the catch and twist the the detector counter-clockwise. A screw can be added to prevent removal from the base.
Before mounting the PROSiXHEATV detector permanently, conduct a Walk Test to verifiy adequate signal strength and adjust the device location and orientation as necessary. Refer to the Limitation of Fire alarm systems document for detailed information on detector spacing, placement zoning and special applications. The detector can be mounted on the ceiling or on the wall. Select a location and mount using the included mounting hardware.
The detector should be tested immediately after installation and at least once a year. Notify the central station that the heat detector is undergoing tests, so we do not dispatch the authorities. You may choose to test the detector by; pressing the Test Button or Direct Heat Test (by using a hair dryer spaced 12" or further away and blowing heat at the sensor). The PROSiXHEATV has a built-in 85dB sounder to alert occupents of any impending danger. To clean the detector, carefully vacuum the side vents all the way around, then, wipe them with a clean damp cloth and dry thoroughly. Do NOT attempt to take the detector apart. This could result in damaging the unit.
Product Features:
- 128-bit AES Encryption (PROSiX-Series)
- Fixed Heat above 135°F
- Rapid Rate-of-Rise of 15°F/minute
- Built-in 85dB Siren
- Base Tamper
- LED indicators
- 360° Detection Pattern
- One-Go / All-Go Feature
ProSeries PROSiXHEATV Product Documents:
• ProSeries PROSiXHEATV Wireless Heat Detector - Data Sheet
• ProSeries PROSiXHEATV Wireless Heat Detector - Applications Guide
• ProSeries PROSiXHEATV Wireless Heat Detector - Limitations Guide
ProSeries PROSiXHEATV Product Specifications:
- Dimensions (Diameter): 4.5" (114mm)
- Mounting Hardware: Included
- Tamper Protected: Yes
- LED Indicators: Yes
- Detection Pattern: 360 degrees
- Siren: Built-in 85dB sounder
- Frequency: 2.4 GHz
- Power Requirements: 3V CR123 battery (Qty 2; Panasonic CR123A, Duracell DL123A, Resideo 466)
- Encryption: 128-bit AES
- Operating Temperature: 40° to 135°F (4° to 57°C)
- Relative Humidity: 95%, non-condensing
- Agency Approvals: FCC/IC-ETL Listed to UL 269, cETL Listed to ULC S530 and S531
- Authorized Countries: US, Latin America
Product Reviews
Other customers rated this item:
5 out of 5 stars
5 out of 5 stars Excellent product for reducing false alarms!, May 26, 2022 Excellent Quality and Functionality, January 23, 2022Posted By: HULLAH
Received alarm shortly after ordering. It was easy to install and to activate. The alarm looks really nice and is very loud when tested. Love that it has a light in it that will go off if we have a problem. Definitely worth the money, and works just as I had hoped. Highly recommend it!
Received alarm shortly after ordering. It was easy to install and to activate. The alarm looks really nice and is very loud when tested. Love that it has a light in it that will go off if we have a problem. Definitely worth the money, and works just as I had hoped. Highly recommend it!
